M25PVMN6TP TR Micron Technology Inc. | M25PVMN6TPCT-ND Digi- Key Part Number, M25PVMN6TPCT-ND HTML Datasheet, M25P M25PVMN6P STMicroelectronics NOR Flash 16MBIT SFLASH MEM datasheet, inventory & pricing. Part, M25P Category. Description, 16 Mbit, Low Voltage, Serial Flash Memory With 50 MHZ Spi Bus Interface. Company, ST Microelectronics, Inc. Datasheet.
|Published (Last):||22 August 2014|
|PDF File Size:||8.91 Mb|
|ePub File Size:||8.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
This is pulled, internally, to V ssand must not be allowed to be connected to any other voltage or signal line on the PCB. Generally, this capacitor is of the order of nF. S wide – lead Plastic Small Outline, mils body width, mechanical data Symbol millimeters inches Typ.
Full text of “Datasheet: M25P16”
Normally, the device is kept selected, with Chip Select S driven Low, for the whole duration of the Hold condition. This is shown in Figure 6. When set to 1such a cycle is in progress, when reset to 0 no such cycle is in progress. The maximum ratings related to soldering conditions are also marked on the inner box label.
M25P16 Datasheet(PDF) – STMicroelectronics
It is also possible to read the Status Register continuously, as shown in Figure 1 1. Value datashset tvsL min ano! If the 8 least significant address bits A7-A0 are not all zero, all transmitted data that goes beyond the end of the current page are programmed from the start address of the same page from the address whose 8 least significant bits A7-A0 are all zero. Ordering information scheme Example: Write In Progress bit behavior specified at Power-up see Section 7: Document promoted to Preliminary Data.
Information in this document supersedes and replaces all information previously supplied. Chip Select S must be driven High after the eighth bit of the instruction code has been latched in, otherwise the Deep Power-down DP instruction is not executed.
D2 Max should not exceed D – K-2 x L.
Chip Select S can be driven High after any bit of the data-out sequence is being shifted out. Page Program PP instruction sequence 29 Figure m25;16 AC characteristics Grade 6 40 Table 1 6. Chip Select S must be driven High after the eighth bit of the last address byte has been latched in, otherwise the Sector Erase SE instruction is not executed.
The Deep Power-down mode automatically stops at Power-down, and the device always Powers-up in the Standby mode. The Bulk Erase BE instruction is ignored if one, or more, sectors are protected.
For optimized timings, it is recommended to use the Page Program PP instruction to program all consecutive targeted Bytes in a single sequence versus using several Page Program PP sequences with each containing only a few Bytes see Table The logic inside the device is held reset while Vqc is less than the Power On Reset POR threshold voltage, V W – all operations are disabled, and the device does not respond to any instruction.
Datqsheet measurement conditions Symbol Parameter Min.
M25P16 SPI flash memory + LPC1769 – prototype work great, designed PCB not so good…
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. Note 1 added to Table Thus, the whole memory can be viewed as consisting of 81 92 pages, or 2 bytes. Block diagram 16 Figure 8.
The device is first selected by driving Chip Select S Low. Output Hi-Z is defined as the point where data out is no longer driven. AC measurement conditions 38 Table The circle in the top view of the package indicates the position of pin 1. Absolute maximum ratings Symbol Parameter Min.
The memory can be programmed 1 to bytes at a time, using the Page Program instruction. Drawing is not to scale. Bus master and memory devices on the SPI bus 10 Figure 5. The instruction sequence is shown in Figure Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Data retention and endurance and Table Search the history of over billion web pages on the Internet.
Unit fc fc Clock Frequency for the following instructions: Chip Select S must be driven High after the eighth bit of the data byte has datassheet latched in. The old-style Electronic Signature is supported for reasons of backward compatibility, only, and should not be m5p16 for new designs. It receives instructions, addresses, and the data to be programmed. All ST products are sold pursuant to ST’s terms and conditions of sale.
Grade 3 temperature range added.
Once ratasheet the Stand-by Power mode, the device waits to be selected, so that it can receive, decode and execute instructions. Hold condition activation 15 Figure 7. Protected area sizes 14 Table 3.
The instruction set is listed in Table 4.